One thing I noticed is some of the case are labeled row x column and some column x row. I believe the standard is row x column, so the cornes, for example, should be 3x6.

My thought was if this would be able to be controlled on a regular MX switch and if such a program already exists?

No. Most MX switches feature a mechanical switch that moves actual metal pieces to complete a physical circuit by coming into contact with each other at the actuation point. It has neither the ability to detect where in the keystroke it is nor alter the point at which the metal pieces make contact.

I say “most” because there is a thing called an “optical switch” which can have this type of capability, and they DO make this in an MX form factor, but you can’t just use these in any MX compatable board, it would need to be a board designed to work with optical MX switches.

How much of this was soldered by you vs the pcb manufacture? Boards without a separate MCU have always fascinated me, but I haven’t been able to price one out because haven’t been able to figure out how to use JLBPCP’s pcb assembly service.

I think this is the most keys I’ve seen crammed into such a low-pin controller. Did you have to do anything special to get the whole matrix in there?

It could take a lot of shapes. It could look like https://www.beeraider.com/one-handed-keyboard/ or https://tipykeyboard.com/en/?v=fa868488740a or you could check out the split keyboards here with 80+ keys https://jhelvy.shinyapps.io/splitkbcompare/

There are a few different options, though none of them are without trade-offs.

1. You could try getting a pointing device integrated into your keyboard, like a trackpad, trackpoint, or trackball that could be used with a single finger while the rest of the fingers are more or less still in the home position. For example, a tractyl.
2. You configure your left hand side (assuming you mouse with the right) to have extra layers which give access to a full keyboard from just that hand. The first thing I would do here is figure out how much you really need to access… Do you just need copy/paste/cut? Do you just need alpha keys? Do you really need a full keyboard including symbols and alt, F-keys, etc? For an extreme version of this, this keyboard using a Taipo layout gives either hand access to a FULL keyboard with only 11 keys per hand, and you have almost 3 times as many keys to work with. You can type entirely with just the left side or entirely with just the right side with that keyboard, though going that small will have a steep learning curve.
3. Get something with even more keys than a sofle, but for just the left split, and you’d only use those extra keys while one handed typing, so each one of those keys is a duplicate function that can be achieved in a different way when you’re using both hands. You could even use a 60% keyboard as your left split, as it would mostly just invade the space between the keyboards which you might have free due to the split.

The most popular 36 key layout is probably miryoku. It uses home row mods for ctrl, shift, etc. A lot of people start with this layout out of the box and then customize from there.

The way the pinky row meets your pinky in the final picture is really satisfying. Its hard to tell using just the last picture, but I think your typing position has your fingers a bit more extended than mine and your typing, while still largely with the tips of your fingers, I’m even closer to the direct tips than you are with more finger curl while typing.

If I do the same smiley-face exercise, I only get the smiley-face if I don’t bend my knuckles very far. As I curl my fingers in more towards either my knuckles or center of my hand, the smiley face disappears and even eventually inverts (though that inversion happens far past what would be comfortable for typing). The amount of curl I have for my normal typing is pretty neutral and doesn’t really make the smiley face.

I installed my battery after installing my nice!nano, so no, you wouldn’t need to desolder your controller to install the battery, even if you directly solder your controller instead of using sockets.

You don’t need the batteries as long as you leave them plugged into the USB-C the whole time. Since you need one side plugged in the whole time, it doesn’t really matter which side you install the one battery… which side would be least intrusive to have a wire running on your desk? The main side (usually defaults to the left side, but can be configured to whichever side you want) does consume more power, so the battery won’t last as long on that side.

If you’d like to use the Bluetooth to connect to multiple devices, maybe put the battery on the main side. The USB cable on the peripheral side is only for charging and flashing and can’t be used for connecting the keyboard to be used as a wired keyboard. By default, plugging in the main side to a computer will switch it to a wired connection to just that device, though, again, whether the wired connection or bluetooth connection should be prioritized can be configured.

Here is a battery guide for the ferris sweep. : https://docs.beekeeb.com/other-guides/installing-a-battery-to-the-ferris-sweep-v2

The battery was the last part that I soldered on my corne build, though if you have a case you’ll have to unscrew the case to do more soldering later.

The design is split into two parts and are connected with print-in-place magnets. Meaning that the print is paused at a certain height and the magnets are inserted into the print. The print is then resumed and the magnets are encased in the print.

https://github.com/Wesztman/brain/tree/main/3d-prints/travel-case#design

If you’re interested in trying to go even smaller, check out Ben Vallack’s video about his 16 key layout. He mentions in the video maybe wanting to switch to an 18 key layout and what he’d do with those extra keys, and he did eventually move to 18 keys.

I’m a huge fan of the ergomechkeyboards and probably spent more than half my time on reddit on that subreddit making sure to read every post.

Thanks for linking to this lemmy community in the restricted message as a way to both keep the community I love together and offering a fix for my addiction in this downtime. I’d be more than happy if we just stayed here regardless of what happens to reddit.

Eventually going restricted sounds good. I have some comments bookmarked I like to reference and occasionally want to search the archive for things, but keeping it fully dark for now makes sense.

Functional as in it technically works or that its comfortable and realistic to use?

Mx spacing is 19.05mmx19.05mm. Choc spacing is typically 18mmx17mm. And this is 16.5mmx16.5mm? Maybe its just your hands but those appear even smaller than that.