You are correct, the agile trait reduces the MAP penalty on its own attack and isn’t dependent on the previous attack being agile.

In general, for a small damage dice size difference, I believe agile is about equal in damage on average. Consider that for an average 1 damage difference between a d6 and d8, agile will miss 5% less and crit 5% more at MAP-4 than a d8 at MAP-5. This difference becomes even greater at MAP-10 vs MAP-8, becoming now actually wholly worth it. However, the value of a third attack is dubious as usual and so while it is strictly better here on average that doesn’t mean it’s actually worth doing (and if it’s not worth doing, then whatever value it has here is most likely to be discarded)

However, a dice size increase is worth roughly two traits (you can see this by comparing average quantity of traits across damage dice size) which means agile is one trait worth two during MAP as it averages out to equal with a weapon of a bigger size.

This means that a d4 weapon with like 5 traits where one of them is agile has a ‘trait’ economy of 6 traits during MAP as it averages a d6 weapon’s damage but still retains the other 4 traits it only gets due to being d4 compared to the 2-3 total that a d6 might have.

I don’t have raw numbers for an extreme example I.e. d12 and a d4 agile but the rule of thumb is it pans out super slightly ahead on average in small dice size differences iirc

EDIT: To note, this doesn’t factor in situations like “what if the monster is one hit from death and I need more accuracy to secure that it dies NOW because it’s a priority target?” as it is difficult to calculate in whiteboard math, but it’s entirely possible that agile pulls ahead with weighted statistics.

Also to note is this doesn’t necessarily apply to monsters. They have higher stats for the same level and typically have greater accuracy and their trait economy is different. It’s possible that their inflated accuracy makes agile less useful, or that their inflated damage makes the extra crit chance from agile better, but I can’t quite say off the cuff.

Still, the TLDR I suppose is that agile is good if it affords you a trait that a weapon of one damage dice size bigger would never have. Say, if you can’t get a d6 weapon with Reach, then an agile d4 weapon with Reach is just as good during MAP, but also has reach. That’s about it.

Most people here have already given you good answers. I’ll just add to this by saying it depends on too many other factors, and add some of my own experience and calculating to support what other people are saying.

TL;DR : It doesn’t matter, it’s like around 1 DPR (damage per round) difference. If you care, use a DPR calculator to work out your ideal options

As far as I am aware, there are no agile attacks that have a damage dice higher than a d6 (for PCs), so my math will be done assuming that.

The Third Attack

The way the math works out, you should want to use an agile attack for the third attack. It will be very unlikely to hit or crit, but it grants a better DPR than using a non-agile attack.

The Second Attack

As for the second attack, it depends heavily on multiple factors:

1. What is the difference in dice size between the agile and non-agile attack, and how many damage dice do you have?

Higher differences in dice sizes will make the non-agile attack more preferable, as though you’re 5% less likely to hit or crit, the damage if you do hit statistically makes up for that. Larger amounts of damage dice exacerbates this effect, as your non-agile weapon will pull a larger gap to the agile weapon.

2. What is your damage roll modifier?

A larger damage roll modifier rewards hitting more often, so agile weapons become more favorable if the modifier is larger. This also includes things such as the damage runes, where the damage dice of your weapon is irrelevant.

3. What chance do you have of critting or hitting the target?

If you have the chance to crit on rolls that are not nat 20s, your DPR with the non-agile weapon begins to trump the agile weapon. This is due to the crit doubling the difference due to damage dice size. The exact point at which this occurs depends on the above two factors as well.

Weirdly the DPR starts to swing the other way as the target’s AC gets higher. As you exceed a roll of 9 needed to hit a target, your chance to crit is static at 5% (nat 20). This reduces the effectiveness of the agile weapon, but after that, the agile weapon starts to claw back its effectiveness as the non-agile weapon’s ability to hit shrinks. Again, the exact point at which this occurs depends on the above two factors.

Graphs

I plotted a few graphs to illustrate the above considerations. The attack roll modifier refers to the attack roll without any MAP, and the DPR calculations have factored in the MAP for the agile and non-agile weapons.

The first is a graph with a d8 non-agile weapon, a d6 agile weapon, and a +4 damage roll modifier.

Note the scale of the axis on the left, it doesn’t make a significant difference for this set of stats.

Now what about a level 4 character without any class bonuses to damage, with the same weapons with all the expected fundamental runes, doubling their damage dice?

Note the fact that there isn’t even a window where the agile weapon is good against weaker enemies, but it claws back much more effectiveness. This is what we’d expect due to the larger amount of damage dice.

Lastly to illustrate the effect of flat modifiers, I put up a level 7 swashbuckler with an Dueling Spear (d8 finesse) against a Shortsword (d6 agile finesse). They will have panache, and are making these strikes non-finishers. The weapons both have the expected fundamental runes, and a flaming rune.

Note how there is a larger range of ACs where an agile weapon is better.

Conclusions

The answer is it depends, as it always does. I can’t give you a definite answer for every single scenario, because there are way too many, and I’m not your dad. In general the following you should make the second strike with an agile weapon if any of these conditions are true:

• If you would crit on a 18-19 without MAP (usually creatures 3-4 levels below you if you are a non-fighter martial)
• If you are fighting a creature with an AC 10+ higher than your hit modifier (usually creatures on your level or higher)
• If you have large damage modifiers
• If the difference in dice size isn’t too large

Otherwise, use you should use your non-agile weapon to make the second strike.

Note that the difference in DPR is small (it’s like 1.2 at most), so it doesn’t really matter which you choose. I’d go with an agile attack if I wanted consistency, and non-agile if I wanted burst.

That’s it! If you read through all of this, thanks for reading my insane ramblings. There are many more things I probably forgot to account for, but I can’t think of them right now, and I accidentally overwrote the sheet for the second graph. I’m gonna go do something more productive now.

IIRC, the -4 isnt worth the damage die drop, but the -8 is. It’s also worth it on specialized features that only work with agile weapons.

From a GMs perspective, there are occasionally mobs who are trying to hit above their level, and have nothing better to do than go all out on their attacks. I usually have them switch to their agile attack for their second and third attack, because they are trying hard just to hit.

You will need to:

1. average the damage of the agile attack

2. average the damage of the non-agile attack

3. multiply both by their chance to hit (taking crits in consideration). You can find an average AC per level here.

On your reading of the rules: The agile weapon list has a lot of weapons that were used alongside bigger weapons irl (dagger, wakizashi, main-gauche). I assume your reading is correct.