Cables are fine until that stupid clip breaks off and every nudge unplugs the fucking cable ever so slightly that it doesn’t work but you can’t see it.
Get a crimp tool and a 50-pack of connectors. If one breaks, it takes all of 60 seconds to re-crimp the end and you’ll only lose about an inch of cable length.
I re-cabled my entire apartment when I first moved in. Best decision I ever made. I just used the existing Cat5 lines to pull my Cat6a instead. Apartment got a free upgrade to Cat6a (which they never even knew about, because I wasn’t going to lose a deposit over something stupid like “unapproved upgrades”) and I got my tasty gigabit.
I was trying to download Red Dead Redemption 2. It was like 120GB, and was going to take hours at 10Mbps on the existing Cat5. I quickly said “fuck that, I can run new lines in 45 minutes and have the download done in 20 minutes with gigabit.” Sure enough, about an hour later, I was playing my game.
I had whatb I assumed was a fault modem/router from the isp and one of the ports ran at 100mbps while the other ran at 1000. I figured this out when it took forever to transfer a file that was just a few gb.
I remember running out of those at work, & intentionally crushing the cheap-ass crimp-tool in my hand, just so I could finish up the next day with pass-through connectors & my Klein tool, rather than spend the next two hours re-terminating connectors that I ‘should have’ gotten exactly right the first time.
I have zero experience with networking hardware. How hard is it to recable an apartment for a newb like me? How does that even work, do I gotta pull wires out of the walls?
Adding new connectors means you only need about an inch extra on each side. Very low skill required if you have the (cheap) tools to do it. Actually putting new wires in place is a bit harder but still fairly easy. Attach some string to the old cable, pull it all the way through the walls. Attach the new cable to the string, then pull that through the walls. Then just add the connectors like the other scenario.
If the holes are sized for a single ethernet cable, you won’t be able to pull through two. If your confident holes are all oversized, sure go for it. Otherwise you risk getting it stuck half way through a wall and pulling the two cables apart
Replacing connectors is east, but won’t solve your problem if the issue is bad cables in the walls. Pulling new cables entirely depends on how well they were installed. A lazy install will actually be much easier to replace, because a lazy installer won’t bother stapling cables in place. They’ll just run the cables across the attic/crawl space and leave it where it lands.
If you’re lucky and got a lazy installer, then you can be equally lazy; The old cable in the wall is going to be your pull line for your new cable. Step 1 is figuring out which lines are which. This is easier with something like a cable sniffer, but there are a few ways to do it. But assuming you know which cables are which, the rest is fairly straightforward.
Use electrical tape to affix the old cable to the new one. Just make a bend on each cable, hook the resulting bends together, then wrap them tightly with electrical tape. The bends hooked together allow the cable to hold the strain, rather than the adhesive on the tape. And you want to use electrical tape because it stretches. Pulling it tight when you wrap ensures that the tape will compress the cables with every wrap. You also want to try to make the connection as “smooth” as possible, so it won’t snag on anything when you pull it.
Now that the old cable is attached to the new, just grab the other end of the old cable and start pulling. It’ll drag the new cable through the wall for you as you pull it out of the wall. Fair warning this is much easier if you have someone feeding the new cable in as you pull, to ensure it doesn’t snag on anything as it enters the wall. It also only reliably works on installs without a lot of bends and corners; Every corner you have to pull around is another potential corner to get snagged on. If you get snagged, sometimes pulling it backwards (tugging on the new cable entering the wall) can help you reset to try again. But sometimes there’s no replacement for good old fashioned legwork; If you get really stuck, or your tape comes undone, or your cable breaks from the strain, you may need to go crawling around your attic to fix it. This is a fast method, but it’s not 100% reliable.
This is why Pro level is to terminate all of your permanent cabling with punch down jacks and patch panels, then use throw-away patch cables from jacks to devices.
All of money and downtime I save from replacing broken RJ45 plugs more than covers the $10 tool and extra $2 that it costs for a keystone jack and wall mount box.
Cables are fine until that stupid clip breaks off and every nudge unplugs the fucking cable ever so slightly that it doesn’t work but you can’t see it.
Get a crimp tool and a 50-pack of connectors. If one breaks, it takes all of 60 seconds to re-crimp the end and you’ll only lose about an inch of cable length.
I re-cabled my entire apartment when I first moved in. Best decision I ever made. I just used the existing Cat5 lines to pull my Cat6a instead. Apartment got a free upgrade to Cat6a (which they never even knew about, because I wasn’t going to lose a deposit over something stupid like “unapproved upgrades”) and I got my tasty gigabit.
I was trying to download Red Dead Redemption 2. It was like 120GB, and was going to take hours at 10Mbps on the existing Cat5. I quickly said “fuck that, I can run new lines in 45 minutes and have the download done in 20 minutes with gigabit.” Sure enough, about an hour later, I was playing my game.
I had whatb I assumed was a fault modem/router from the isp and one of the ports ran at 100mbps while the other ran at 1000. I figured this out when it took forever to transfer a file that was just a few gb.
Make sure to get pass-through RJ45 connectors.
It’s 10x easier to trim the excess after crimping, rather than getting the lengths spot on before.
I remember running out of those at work, & intentionally crushing the cheap-ass crimp-tool in my hand, just so I could finish up the next day with pass-through connectors & my Klein tool, rather than spend the next two hours re-terminating connectors that I ‘should have’ gotten exactly right the first time.
Dunno, I have no problems with regular RJ45 connectors.
I have zero experience with networking hardware. How hard is it to recable an apartment for a newb like me? How does that even work, do I gotta pull wires out of the walls?
Adding new connectors means you only need about an inch extra on each side. Very low skill required if you have the (cheap) tools to do it. Actually putting new wires in place is a bit harder but still fairly easy. Attach some string to the old cable, pull it all the way through the walls. Attach the new cable to the string, then pull that through the walls. Then just add the connectors like the other scenario.
Pull the new cables taped to the old cables, no need for the string step.
If the holes are sized for a single ethernet cable, you won’t be able to pull through two. If your confident holes are all oversized, sure go for it. Otherwise you risk getting it stuck half way through a wall and pulling the two cables apart
Fair point. I’m an electrician by trade so i hate it people drill holes that small, but it does happen.
Replacing connectors is east, but won’t solve your problem if the issue is bad cables in the walls. Pulling new cables entirely depends on how well they were installed. A lazy install will actually be much easier to replace, because a lazy installer won’t bother stapling cables in place. They’ll just run the cables across the attic/crawl space and leave it where it lands.
If you’re lucky and got a lazy installer, then you can be equally lazy; The old cable in the wall is going to be your pull line for your new cable. Step 1 is figuring out which lines are which. This is easier with something like a cable sniffer, but there are a few ways to do it. But assuming you know which cables are which, the rest is fairly straightforward.
Use electrical tape to affix the old cable to the new one. Just make a bend on each cable, hook the resulting bends together, then wrap them tightly with electrical tape. The bends hooked together allow the cable to hold the strain, rather than the adhesive on the tape. And you want to use electrical tape because it stretches. Pulling it tight when you wrap ensures that the tape will compress the cables with every wrap. You also want to try to make the connection as “smooth” as possible, so it won’t snag on anything when you pull it.
Now that the old cable is attached to the new, just grab the other end of the old cable and start pulling. It’ll drag the new cable through the wall for you as you pull it out of the wall. Fair warning this is much easier if you have someone feeding the new cable in as you pull, to ensure it doesn’t snag on anything as it enters the wall. It also only reliably works on installs without a lot of bends and corners; Every corner you have to pull around is another potential corner to get snagged on. If you get snagged, sometimes pulling it backwards (tugging on the new cable entering the wall) can help you reset to try again. But sometimes there’s no replacement for good old fashioned legwork; If you get really stuck, or your tape comes undone, or your cable breaks from the strain, you may need to go crawling around your attic to fix it. This is a fast method, but it’s not 100% reliable.
No pulling wires from walls, just cutting the ends off and installing new connectors. Might not be enough in every case though.
Crimping took me like 5 attempts to get right when I learned it in school.
I have a collection of 3d prints on thingiverse that reattach that part. Highly recommend.
This is why Pro level is to terminate all of your permanent cabling with punch down jacks and patch panels, then use throw-away patch cables from jacks to devices.
Look at mr moneybags with their fancy data closet.
It’s not that expensive… you can buy a home punch down board for cheap, just need some space. You don’t need an actual rack.
All of money and downtime I save from replacing broken RJ45 plugs more than covers the $10 tool and extra $2 that it costs for a keystone jack and wall mount box.
It’s pretty easy to crimp a new one back on, and even easier with a 30 dollar tool.
Easy fix with a tight layer of electrical tape to act as a wedge. You can also shove a toothpick in the top for extra staying power.
Haha true story
Crimp tool: 2$
100 RJ45: 3$
Your problem will be solved for rest of you life and life of your children for 5 dollars.